Ghost 2 Immobiliser Reviews
The Ghost 2 immobiliser utilizes modern technology to stop car theft. This hidden device is not noticed by thieves, and it only starts the engine after a PIN or app is entered.
It's weatherproof and connects to the CAN data network of your vehicle. It comes with a service/valet feature that allows you to temporarily start your vehicle while it is in the garage.
Easy to install
The Ghost immobiliser is a cutting-edge security device that safeguards your vehicle from hacking, cloning, and key theft. It utilizes an PIN code system that is integrated into your vehicle's electronic control unit, making it impossible for thieves to recognize. It's not visible and does not use any sensors or special keys. It is also cheaper than replacing an ECU or installing a new key fob and can lower your monthly insurance premiums.
Follow the directions of the manufacturer when installing a Ghost 2 vehicle immobiliser. This will ensure that the device is working correctly and efficiently. Once the installation is complete check the system by entering the PIN code, then turning on the engine. Regular testing will allow you to identify any problems before they get worse.
Before starting the installation, ensure the position of the CAN H and CAN L wires. They are essential to power the immobiliser, therefore it is essential to ensure that they are connected correctly. Labeling the wires will help you locate them when installing. Once you have identified the location of these wires, connect them to a permanent 12V power source as well as the grounding point. Use a fuse tap to shield the connections from damage or short-circuits.
After connecting the wires, neaten the wires with cable ties to stop alteration. You can also cover the connections using insulation tape or heat-shrink tubing. This will protect the device from electrical shorts, and will extend the life of the device. It's a good idea to test your Ghost 2 immobiliser once the wiring is secured.
In situations where you have to surrender your vehicle, for instance for servicing or valet parking or valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. To activate this feature, simply press the brake pedal while holding the accelerator, and press a number of times equal to the first digit of the emergency code. The system will go into service mode. This is confirmed by flashing five times the indicator signal.
Easy to change PIN codes
It is simple to secure your vehicle from theft using an immobiliser ghost 2. It is discreetly installed within the vehicle and can only be accessed using a specific code. The device connects directly to the vehicle ECU through its data bus, and does not rely on radio frequency signals as do traditional Thatcham immobilisers or aftermarket alarm systems. This makes it difficult for thieves to discern the sound of an immobiliser relay or add new key fobs. The control unit is hidden in the vehicle's wiring or dashboard, and cannot be physically tampered to reset the system.
The ghost 2 immobiliser connects to the vehicle's CAN Data network. It makes use of buttons on the door panels, steering wheel and the centre console to create a customized sequence of up to twenty button presses that need to be entered to start the engine - just as a PIN. This unique system can be reprogrammed and does not require cutting wires when installing. You can even start your car in Service or Valet mode when you hand it to a mechanic perform work.
The application can also be used to block your PIN code if you've lost your keys, or change it. This feature is especially useful if you've given your car to someone else for parking or valet services. It stops them from starting it and driving it away without your consent. It's also unnoticeable to professional thieves since it does not use any circuit cuts or radio frequencies.
Another great feature of the ghost 2 immobiliser is its ability to stop relay thefts. Relay theft is a popular method of car theft in which thieves attack the diagnostic port of your car and then alter the signal that is sent by the key to the vehicle's ECU in order to fool it into believing that the key is valid. The traditional immobiliser can be bypassed in this way, but with the ghost 2 immobiliser the signal is blocked by the immobiliser before it gets to the ECU.
Simple to use app
Ghost 2 is a revolutionary immobiliser that protects your car from key-cloning, hacking and key theft. It connects to the CAN data network of your vehicle and requires a PIN code in order to start the engine. It also deters thieves from by using signal spoofing or device spoofing which are common methods of stealing vehicles.
The system is simple to use and works like an ordinary auto alarm. Installing the system allows you to create a unique 20-digit pin code that you must enter before starting the vehicle. This will prevent the vehicle from being stolen even the case that you lose your keys. You can disable the system using an app on your smartphone.
Contrary to other systems it is completely silent and does not emit radio frequency signals. It is a weatherproof, discreet device that can be installed anywhere in your vehicle. It can be easily hidden under the dash, steering wheel, or on the door panels. It communicates with your ECU over the CAN data circuit, and is not affected by diagnostic tools, which some thieves use to find security systems. It is not affected by jamming devices that can spoof codes.
It is a covert system that can be used to deter the theft of all vehicles. Its technology has been proven to be efficient, and it is in line with TASSA Standards. The Ghost is a good choice for classic or sports automobiles. It can also be used as a method to safeguard vehicles rented on apps like Turo.
The Autowatch Ghost 2 is the next generation of vehicle immobilisers. The Keylab is inaccessible to thieves, and blocks them starting your vehicle without your PIN, or unless they have been authorized by the app. It does not emit radio frequencies or any other signals scanners could detect. Installation is fast and simple. The app is simple to navigate and offers a user-friendly interface which allows for easy configure and use. It also comes with a GPS tracker to help police locate and recover the vehicle.
Simple to reset
It is possible to secure your vehicle from theft using an immobiliser ghost 2. It works with your vehicle's ECU to create a security barrier that thieves can't breach without the correct PIN. It's also TASSA verified which means it's recognized by insurance companies. It's a useful tool to deter theft of your car and could save you money in the end.
Contrary to traditional alarms/immobilisers which require cutting circuits and circuit cutting, the Ghost system is connected directly to the vehicles CAN data network and works using your existing buttons on the dashboard and steering wheel. You can create a unique pin that can be up to 20 presses in length. This PIN has to be entered before the engine can be started the same way as the credit card's PIN. The Ghost system is inaccessible to thieves, and there are no LEDs to indicate its presence. This makes it the most efficient aftermarket CAN-bus immobiliser available today.
Another advantage of the Ghost system is that it does not utilize radio frequency signals, meaning it is not scannable or intercepted by thieves. This prevents cloned keys and relay attacks as well as the more usual method of hacking a vehicle's CAN bus system by scanning for signals from its alarm or immobiliser. In addition to this, the Ghost system is designed to be completely hidden inside your vehicle and there are no LEDs or signals that indicate its presence.
The system has a Transport Mode which disables the Ghost System. This is beneficial in situations where you may require temporarily deactivating Ghost such as when you're transporting or servicing your vehicle. However this mode isn't as effective as Service Mode, as it does not turn off the Ghost system when your vehicle speeds over 31 mph for more than 15 minutes.
To reset your ghost 2 immobiliser you will need to have the emergency code, which is available from your installer. It is typically hidden under a scratch-off section on the card provided when you installed the device. This emergency code should be secured and stored in a secure location like your wallet at home.